(or -i) command line argument to the test, or by setting GIT_TEST_OPTS
appropriately before running "make".
+-v::
--verbose::
This makes the test more verbose. Specifically, the
command being run and their output if any are also
numbers matching <pattern>. The number matched against is
simply the running count of the test within the file.
+-d::
--debug::
This may help the person who is developing a new test.
It causes the command defined with test_debug to run.
failed tests so that you can inspect its contents after
the test finished.
+-i::
--immediate::
This causes the test to immediately exit upon the first
failed test. Cleanup commands requested with
in order to keep the state for inspection by the tester
to diagnose the bug.
+-l::
--long-tests::
This causes additional long-running tests to be run (where
available), for more exhaustive testing.
+-r::
+--run=<test-selector>::
+ Run only the subset of tests indicated by
+ <test-selector>. See section "Skipping Tests" below for
+ <test-selector> syntax.
+
--valgrind=<tool>::
Execute all Git binaries under valgrind tool <tool> and exit
with status 126 on errors (just like regular tests, this will
test, or t[0-9]{4} followed by ".$number" to say which
particular test to skip.
-Note that some tests in the existing test suite rely on previous
-test item, so you cannot arbitrarily disable one and expect the
-remainder of test to check what the test originally was intended
-to check.
+For an individual test suite --run could be used to specify that
+only some tests should be run or that some tests should be
+excluded from a run.
+
+The argument for --run is a list of individual test numbers or
+ranges with an optional negation prefix that define what tests in
+a test suite to include in the run. A range is two numbers
+separated with a dash and matches a range of tests with both ends
+been included. You may omit the first or the second number to
+mean "from the first test" or "up to the very last test"
+respectively.
+
+Optional prefix of '!' means that the test or a range of tests
+should be excluded from the run.
+
+If --run starts with an unprefixed number or range the initial
+set of tests to run is empty. If the first item starts with '!'
+all the tests are added to the initial set. After initial set is
+determined every test number or range is added or excluded from
+the set one by one, from left to right.
+
+Individual numbers or ranges could be separated either by a space
+or a comma.
+
+For example, to run only tests up to a specific test (21), one
+could do this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1-21'
+
+or this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='-21'
+
+Common case is to run several setup tests (1, 2, 3) and then a
+specific test (21) that relies on that setup:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1 2 3 21'
+
+or:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run=1,2,3,21
+
+or:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='-3 21'
+
+As noted above, the test set is built going though items left to
+right, so this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='1-4 !3'
+
+will run tests 1, 2, and 4. Items that comes later have higher
+precendence. It means that this:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='!3 1-4'
+
+would just run tests from 1 to 4, including 3.
+
+You may use negation with ranges. The following will run all
+test in the test suite except from 7 up to 11:
+
+ $ sh ./t9200-git-cvsexport-commit.sh --run='!7-11'
+
+Some tests in a test suite rely on the previous tests performing
+certain actions, specifically some tests are designated as
+"setup" test, so you cannot _arbitrarily_ disable one test and
+expect the rest to function correctly.
+
+--run is mostly useful when you want to focus on a specific test
+and know what setup is needed for it. Or when you want to run
+everything up to a certain test.
Naming Tests