Synonym for `-p --raw`.
endif::git-format-patch[]
+--minimal::
+ Spend extra time to make sure the smallest possible
+ diff is produced.
+
--patience::
Generate a diff using the "patience diff" algorithm.
---stat[=<width>[,<name-width>]]::
+--stat[=<width>[,<name-width>[,<count>]]]::
Generate a diffstat. You can override the default
output width for 80-column terminal by `--stat=<width>`.
The width of the filename part can be controlled by
giving another width to it separated by a comma.
+ By giving a third parameter `<count>`, you can limit the
+ output to the first `<count>` lines, followed by
+ `...` if there are more.
++
+These parameters can also be set individually with `--stat-width=<width>`,
+`--stat-name-width=<name-width>` and `--stat-count=<count>`.
--numstat::
Similar to `\--stat`, but shows number of added and
number of modified files, as well as number of added and deleted
lines.
---dirstat[=<limit>]::
- Output the distribution of relative amount of changes (number of lines added or
- removed) for each sub-directory. Directories with changes below
- a cut-off percent (3% by default) are not shown. The cut-off percent
- can be set with `--dirstat=<limit>`. Changes in a child directory are not
- counted for the parent directory, unless `--cumulative` is used.
+--dirstat[=<param1,param2,...>]::
+ Output the distribution of relative amount of changes for each
+ sub-directory. The behavior of `--dirstat` can be customized by
+ passing it a comma separated list of parameters.
+ The defaults are controlled by the `diff.dirstat` configuration
+ variable (see linkgit:git-config[1]).
+ The following parameters are available:
+
-Note that the `--dirstat` option computes the changes while ignoring
-the amount of pure code movements within a file. In other words,
-rearranging lines in a file is not counted as much as other changes.
-
---dirstat-by-file[=<limit>]::
- Same as `--dirstat`, but counts changed files instead of lines.
+--
+`changes`;;
+ Compute the dirstat numbers by counting the lines that have been
+ removed from the source, or added to the destination. This ignores
+ the amount of pure code movements within a file. In other words,
+ rearranging lines in a file is not counted as much as other changes.
+ This is the default behavior when no parameter is given.
+`lines`;;
+ Compute the dirstat numbers by doing the regular line-based diff
+ analysis, and summing the removed/added line counts. (For binary
+ files, count 64-byte chunks instead, since binary files have no
+ natural concept of lines). This is a more expensive `--dirstat`
+ behavior than the `changes` behavior, but it does count rearranged
+ lines within a file as much as other changes. The resulting output
+ is consistent with what you get from the other `--*stat` options.
+`files`;;
+ Compute the dirstat numbers by counting the number of files changed.
+ Each changed file counts equally in the dirstat analysis. This is
+ the computationally cheapest `--dirstat` behavior, since it does
+ not have to look at the file contents at all.
+`cumulative`;;
+ Count changes in a child directory for the parent directory as well.
+ Note that when using `cumulative`, the sum of the percentages
+ reported may exceed 100%. The default (non-cumulative) behavior can
+ be specified with the `noncumulative` parameter.
+<limit>;;
+ An integer parameter specifies a cut-off percent (3% by default).
+ Directories contributing less than this percentage of the changes
+ are not shown in the output.
+--
++
+Example: The following will count changed files, while ignoring
+directories with less than 10% of the total amount of changed files,
+and accumulating child directory counts in the parent directories:
+`--dirstat=files,10,cumulative`.
--summary::
Output a condensed summary of extended header information
projects, so use it with caution. Giving more than one
`-C` option has the same effect.
+-D::
+--irreversible-delete::
+ Omit the preimage for deletes, i.e. print only the header but not
+ the diff between the preimage and `/dev/null`. The resulting patch
+ is not meant to be applied with `patch` nor `git apply`; this is
+ solely for people who want to just concentrate on reviewing the
+ text after the change. In addition, the output obviously lack
+ enough information to apply such a patch in reverse, even manually,
+ hence the name of the option.
++
+When used together with `-B`, omit also the preimage in the deletion part
+of a delete/create pair.
+
-l<num>::
The `-M` and `-C` options require O(n^2) processing time where n
is the number of potential rename/copy targets. This
of lines, thereby fusing hunks that are close to each other.
ifndef::git-format-patch[]
+ifndef::git-log[]
--exit-code::
Make the program exit with codes similar to diff(1).
That is, it exits with 1 if there were differences and
--quiet::
Disable all output of the program. Implies `--exit-code`.
+endif::git-log[]
endif::git-format-patch[]
--ext-diff::
--no-ext-diff::
Disallow external diff drivers.
+--textconv::
+--no-textconv::
+ Allow (or disallow) external text conversion filters to be run
+ when comparing binary files. See linkgit:gitattributes[5] for
+ details. Because textconv filters are typically a one-way
+ conversion, the resulting diff is suitable for human
+ consumption, but cannot be applied. For this reason, textconv
+ filters are enabled by default only for linkgit:git-diff[1] and
+ linkgit:git-log[1], but not for linkgit:git-format-patch[1] or
+ diff plumbing commands.
+
--ignore-submodules[=<when>]::
Ignore changes to submodules in the diff generation. <when> can be
either "none", "untracked", "dirty" or "all", which is the default